Project

General

Profile

Discussion and support

General questions, suggestions, tips, tweaks, fixes

Subject Author Created Replies Last message
Need ATMega 168P-20PU with boot loader installed.......... Rolf 2015-04-29 15:43 1 Added by jaap about 7 years ago
RE: Need ATMega 168P-20PU with boot loader installed........
I2C controller locks up HansPeterHaastrup 2014-11-24 17:18 7 Added by jaap about 7 years ago
RE: I2C controller locks up
i2c display atmega won't program twice alan 2015-04-19 18:27 2 Added by alan about 7 years ago
RE: i2c display atmega won't program twice
Laser fails to saturate anode completely, or so i'm guessing. Zilver 2015-03-26 00:17 0
Problems etching hpux735 2015-03-17 18:18 10 Added by hpux735 about 7 years ago
RE: Problems etching
Setting up LS3020 & homing issues jimjiminyjimjim 2014-02-16 22:04 23 Added by jaap about 7 years ago
RE: Setting up LS3020 & homing issues
Questions for Beginners asenyurt 2015-03-17 21:27 15 Added by asenyurt about 7 years ago
RE: Questions for Beginners
Can't make round circles leotuorto 2015-02-20 14:45 6 Added by leotuorto about 7 years ago
RE: Can't make round circles
PWM Strategies hpux735 2014-12-31 06:26 0
SD Card issues, reboot loop. hpux735 2014-12-14 03:41 2 Added by hpux735 over 7 years ago
RE: SD Card issues, reboot loop.
Looking for a new machine 4060 model acubino 2014-11-25 15:32 0
Laser mis-fires ... drogon 2014-08-16 23:00 23 Added by HackerspaceFFM over 7 years ago
RE: Laser mis-fires ...
height adjustment reinoud 2014-09-29 13:57 0
How to laser brown dots on perspex reinoud 2014-09-29 13:05 0
Water flow sensor depronman 2014-08-31 00:34 8 Added by joostn over 7 years ago
RE: Water flow sensor
Dual assist line laser mount for K40 joostn 2014-08-29 17:36 5 Added by depronman over 7 years ago
RE: Dual assist line laser mount for K40
Videoing... drogon 2014-08-20 22:53 0
Light in HPC LS 3020 laser leenvw 2014-08-20 12:15 0
Moshi board for sale joostn 2014-08-17 08:40 0
Engraving tips? drogon 2014-08-16 21:42 3 Added by drogon almost 8 years ago
RE: Engraving tips?
VisiCut & Fractional speeds ... drogon 2014-08-16 20:36 3 Added by t-oster almost 8 years ago
RE: VisiCut & Fractional speeds ...
What stepper motor drivers were supplied with my kit? drogon 2014-08-11 15:55 1 Added by jaap almost 8 years ago
RE: What stepper motor drivers were supplied with my kit?
New HPC LS 3020 Setup drogon 2014-07-09 20:48 11 Added by Springuin almost 8 years ago
RE: New HPC LS 3020 Setup
IP address problems........... Rolf 2014-07-23 17:42 3 Added by drogon almost 8 years ago
RE: IP address problems...........
Help required in getting VISICAM to work under Windows 7 32 bit depronman 2014-07-19 10:05 9 Added by depronman almost 8 years ago
RE: Help required in getting VISICAM to work under Window...
(26-50/143) Per page: 25, 50, 100

Also available in: Atom